Independent Viking service · Tacoma, WA

(206) 472-1140
Viking Dishwasher Repair

Cleaning a Viking Dishwasher with Baking Soda

Viking Repair Tacoma (206) 472-1140 the guide is free; the visit is the only fixed fee
This guideFault Guides
ApplianceViking Dishwasher Repair
Written byHollis Yamada
RoleService technician — refrigeration and cooking
In the trade21 years in the trade
Reading time4 min
If it needs a visit$89, credited to the repair

To clean a dishwasher with baking soda, rinse the filter, scatter one cup over the empty tub floor, then run the hottest short cycle with no detergent.

Built-in dishwasher with its lower access panel removed, exposing the drain pump, hoses and levelling feet

Cleaning a dishwasher with baking soda comes down to four moves: rinse the filter, wipe the door seal, scatter roughly one cup of baking soda across the floor of the empty tub, and run the hottest short program the machine offers with no detergent and no dishes. Soda is mildly alkaline and faintly gritty, so hot water turns it into a gentle scrub that loosens greasy film and kills the stale smell that builds between loads. The method suits any make, from a builder-grade unit to a built-in Viking, and on Tacoma’s soft city water it often does most of the work by itself.

What baking soda can and cannot do

Think of soda as a deodorizer and a degreaser. It lifts the slick layer that coats the tub walls, freshens the sump, and leaves stainless steel looking brighter. It does not dissolve chalky mineral scale; that needs an acid such as white vinegar or citric acid. It will not clear a blocked drain hose or revive a weak pump, and it is no replacement for dishwasher detergent on a normal load.

The baking soda clean, one step at a time

1. Start with the filter

Most odor lives in the filter at the base of the tub, so clean it before anything else. On current Viking built-ins (the VDWU and FDWU lines), twist the micro and coarse filter assembly counterclockwise, lift it out, then slide out the flat filter underneath. Brush all three pieces under running tap water with a soft brush, refit them, and turn until you hear the click. Viking’s manual asks for this at least once a week. Owners of other makes should check their own book, though weekly is a sound habit for any machine.

2. Wipe the door edges and the gasket

The lower lip of the door and the rubber seal sit outside the spray pattern, so drips dry there and turn grimy. Mix a spoonful of soda with enough water to make a paste, work it along the gasket and the door bottom with a soft cloth, then wipe it away with a damp one. Keep steel wool and green scouring pads away from stainless; the scratches they leave hold dirt.

3. Spin the spray arms

Turn each arm by hand. It should rotate freely without catching. If any nozzle holes look plugged with seeds or shards of glass, a toothpick will clear them.

4. Soda in, hot program on

Shake about a cup of baking soda evenly over the floor of the empty tub. Let it sit for at least an hour, or overnight if the smell is strong. Then choose the hottest short program and start it with nothing else inside. When it finishes, wipe any pale residue from the corners with a damp cloth.

Optional: vinegar first, never at the same time

If glasses come out cloudy or the tub shows a white chalky haze, run one empty cycle first with a cup of plain white vinegar in an upright, dishwasher-safe bowl on the top rack, and do the soda step afterward. Combined in one cycle, the two simply neutralize each other. Never pair vinegar with chlorine bleach.

Why soft Tacoma water changes the routine

The city supply is drawn mostly from a protected mountain-river watershed, and the water reaching kitchens from the Proctor District to Northeast Tacoma is soft. That means far less chalky scale than in hard-water regions, so the residue you fight here is mostly grease and leftover detergent. Soft water also makes it easy to overdo detergent and rinse aid. Viking’s VDWU and FDWU machines let you choose between zero and four doses of rinse aid, shown as P:0 through P:4, and they arrive set at 3. If a faint blue streak wipes off a glass with your finger, turn it down a step; if spots or stains linger, turn it up.

A simple maintenance calendar

TaskHow often
Rinse and brush the filtersWeekly
Baking soda cleaning cycleMonthly, or whenever odor returns
Gasket and door-edge wipeMonthly, alongside the soda clean
Spray arm checkEvery few months
Vinegar passOnly when haze or spots appear

A professional tune-up covers the parts a homeowner rarely sees: the inlet valve and its screen, drain pump and hose routing, the door latch and hinges, the leveling feet, and the floor under the toe kick, where a slow leak can hide for months.

When cleaning will not fix it

If water still pools in the tub after a soda cycle and a fresh filter, the trouble is further down the line. Our page on standing water after every cycle walks through the usual culprits. On older Viking models that flash their cycle buttons instead of showing a code, the manual’s checklist for a Drain Timeout covers the sink drain and the disposal knockout plug, clogs and kinks in the hose, the high loop, leveling and the filters.

On VDWU and FDWU machines, E:01 means the dishwasher has sensed overfilling or a leak and is trying to pump out; an E:01 that keeps coming back needs a technician. E:02 means the water supply was interrupted, so confirm the shutoff valve under the sink is fully open. If the machine starts, runs a minute, then stops with lights flashing, that page explains the next checks.

For homes in the North End, the Stadium District and the rest of our area, Viking Repair Tacoma answers at (206) 472-1140. The $89 visit pays for the drive and a full diagnosis, and every dollar of that $89 comes off the bill once you approve the work. Replacing a drain pump or control on a Viking dishwasher typically lands in the $190–$380 range, with the firm price given after diagnosis. Details are on our Viking dishwasher repair page.

Asked after reading this

Can I put baking soda in the detergent cup instead of on the tub floor?

You can, but scattering it across the tub floor works better for a cleaning run. The dispenser only opens partway through the program, so soda sitting in the cup misses the first fill of hot water. For everyday loads keep using proper dishwasher detergent, because soda on its own is too weak to break down baked-on food.

Is it safe to use baking soda and vinegar together in a dishwasher?

It is safe, but pointless in the same cycle, because the acid and the alkali largely cancel each other and the fizz does very little scrubbing. Run the vinegar pass first and the soda pass second. Never let vinegar meet chlorine bleach in the tub.

How often should I clean my dishwasher with baking soda?

Once a month suits most households, plus any time a sour smell creeps back. The filter deserves more frequent attention: Viking tells owners of its current built-in models to rinse it at least weekly, and a clean filter is what lets the monthly soda treatment do its job.

Should my dishwasher drain use a high loop or an air gap?

Either one does the same job, stopping used sink water from flowing backward into your clean tub; the right choice depends on local plumbing code. With a high loop, the hose is fastened as high as possible under the counter before it falls toward the disposal. An air gap is a little chrome cap beside the faucet that opens the line to the air.

Will a baking soda clean fix a dishwasher that will not drain?

Only when the cause is a packed filter. If water still pools after the filter is spotless and the sink drains freely, suspect a kinked hose, a blocked disposal inlet or a tired drain pump, and have the machine diagnosed.

dishwashermaintenancecleaningviking

Book it

Tell us the model, or just take a slot

The $89 visit is credited back once you approve the repair, and you hear the figure before a panel comes off. Viking Repair Tacoma runs visits 8am to 8pm, Monday to Sunday; the line is picked up 24/7.